Fuel properties and incineration behavior of poultry litter blended with sweet sorghum bagasse and pyrolysis oil.

The incineration of poultry litter (PL) effectively reduces the volume of waste in line with the United Nations Sustainable Development Goal of "affordable and clean energy". However, mono-incineration is associated with considerable challenges due to the varying moisture, structural and chemical composition and low energy yield. The aim of the present work was to investigate the influence of sweet sorghum bagasse (SS) and pyrolysis oil (PO) on improving the fuel properties of PL and mitigating ash related burdens during incineration. The different biomass feedstocks were produced by combining PL with SS at 0.0% (T0), 25% (T1), 50% (T2), 75% (T3) and compared with 100% SS (T4). In order to achieve high energy potential and low ash deposition, the parallel samples were additionally mixed with 10% PO to improve the energy value. The experimental results show that increasing the proportion of SS and adding PO to the mixtures increases the volatile matter and decreases the moisture and ash content. The addition of PO also increases the carbon and hydrogen content. The use of SS and PO thus increased the values of the ignitability index and apparently also the flammability by 30.0%-49.4% compared to pure PL. SS and PO shifted the HHV of the starting material from 16.90 to 18.78 MJ kg-1. In addition, SS + PO improved the flame volume and red color intensity of the PL blends based on the image analysis method. However, the presence of SS and PO did not sufficiently improve the ash-related index values, which requires further investigation.

Solidification/stabilization and optimization of municipal solid waste incineration fly ash with aluminosilicate solid wastes.

Alkali-activation is an effective municipal solid waste incineration fly ash (MSWIFA) solidification/stabilization (S/S) technology. However, the characteristics of calcium-rich silica-poor aluminum phase in MSWIFA easily cause the structural instability and contamination of alkali activated MSWIFA S/S bodies. Therefore, the aluminosilicate solid wastes are used in this work to optimize the immobilization and structural properties. Results showed that incorporation of aluminosilicate solid wastes significantly improved the compressive strength and heavy metals pollution toxicity of MSWIFA S/S bodies. Compared to alkali activated MSWIFA, the compressive strength of S/S bodies with addition of coal fly ash, silica fume and granulated blast furnace slag improved by 31.0%, 47.6% and 50.8% when the curing time was 28 days, respectively. Leachability of Pb, Zn and Cd in these alkali activated MSWIFA S/S bodies was far below the threshold value specified in Standard GB16889. Aluminosilicate solid wastes provided abundant Si/Al structural units, and some new phases such as ettringite(AFt, 3CaO⋅Al2O3⋅3CaSO4⋅32H2O), calcium sulfoaluminate hydrate (3CaO⋅Al2O3⋅CaSO4⋅12H2O) and Friedel's salt (CaO⋅Al2O3⋅CaCl2⋅10H2O) can be detected in S/S matrix with aluminosilicate solid wastes, along comes increased the amount of the amorphous phases. Lower Ca/Si molar ratio tended to form the network structure gel similar to tobermorite with higher polymerization degree. Meanwhile, the silica tetrahedron of the gels changed from the oligomerization state like island to the hyperomerization state like chain, layer network or three-dimensional structure, and average molecular chain length increased. These findings provide theoretical basis for structural properties optimization and resource utilization of MSWIFA S/S matrices.

Analysis of composition characteristics and treatment techniques of municipal solid waste incineration fly ash in China.

The rapid development of the economy and society is causing an increase in the amount of municipal solid waste (MSW) produced by people's daily lives. With the strong support of the Chinese government, incineration power generation has steadily become the primary method of treating MSW, accounting for 79.86%. However, burning produces a significant amount of municipal solid waste incineration fly ash (MSWI-FA), which contains heavy metals, soluble chlorine salts, and dioxins. China's MSWI-FA yield increased by 8.23% annually to 7.80 million tons in 2022. Besides, the eastern region, especially the southeastern coastal region, has the highest yield of MSWI-FA. There are certain similarities in the chemical characteristics of MSWI-FA samples from Northeast, North, East, and South China. Zn and CaO have the largest amounts of metals and oxides, respectively. The Cl content is about 20 wt%. This study provides an overview of the techniques used in the thermal treatment method, solidification and stabilization, and separation and extraction of MSWI-FA and compares their benefits and drawbacks. In addition, the industrial applications and standard requirements of landfill treatment and resource utilization of MSWI-FA in China are analyzed. It is discovered that China's resource utilization of MSWI-FA is insufficient through the study on the fly ash disposal procedures at a few MSW incineration facilities located in the economically developed Guangdong Province and the traditional industrial city of Tianjin. Finally, the prospects for the disposal of MSWI-FA were discussed.

Effect of oxide interactions on chromium speciation transformation during simulated municipal solid waste incineration.

Chromium released during municipal solid waste incineration (MSWI) is toxic and carcinogenic. The removal of chromium from simulated MSWI flue gas by four sorbents (CaO, bamboo charcoal (BC), powdered activated carbon (PAC), and Al2O3) and the effects of four oxides (SiO2, Al2O3, Fe2O3, and CaO) on chromium speciation transformation were investigated. The results showed that the removal rates of total Cr by the four sorbents were Al2O3 < CaO < PAC < BC, while the removal rates of Cr(VI) by the four sorbents were Al2O3 < PAC < BC < CaO. CaO had a strong oxidizing effect on Cr(III), while BC and PAC had a better-reducing effect on Cr(VI). SiO2 was better for the reduction of Na2CrO4 and K2CrO4 above 1000°C due to its strong acidity, and the addition of CaO significantly inhibited the reduction of Cr(VI). MgCrO4 decomposed above 700°C to form MgCr2O4, and the reaction between MgCrO4 and oxides also existed in the form of a more stable trivalent spinel. Furthermore, when investigating the effect of oxides on the oxidation of Cr(III) in CrCl3, it was discovered that CaO promoted the conversion of Cr(III) to Cr(VI), while the presence of chlorine caused chromium to exist in the form of Cr(V), and increasing the content of CaO and extending the heating time facilitated the oxidation of Cr(III). In addition, silicate, aluminate, and ferrite were generated after the addition of SiO2, Al2O3, and Fe2O3, which reduced the alkalinity of CaO and had an important role in inhibiting the oxidation of Cr(III). The acidic oxides can not only promote the reduction of Cr(VI) but also have an inhibitory effect on the oxidation of Cr(III) ascribed to alkali metals/alkaline earth metals, and the proportion of acidic oxides can be increased moderately to reduce the generation of harmful substances in the hazardous solid waste heat treatment.

Environmental impacts of valorisation of crude glycerol from biodiesel production - A life cycle perspective.

Biodiesel production produces significant quantities of impure crude glycerol as a by-product. Recent increases in the global biodiesel production have led to a surplus of crude glycerol, rendering it a waste. As a result, different methods for its valorisation are currently being investigated. This paper assesses the life cycle environmental impacts of an emerging technology for purification of crude glycerol - a multi-step physico-chemical treatment - in comparison to incineration with energy recovery commonly used for its disposal. For the former, three different acids (H3PO4, H2SO4 and HCl) are considered for the acidification step in the purification process. The results suggest that the H2SO4-based treatment is the best option with 17 net-negative impacts out of the 18 categories considered; this is due to system credits for the production of purified glycerol, heat and potassium salts. In comparison to incineration with energy recovery, the H2SO4-based process has lower savings for the climate change impact (-311 versus -504 kg CO2 eq./t crude glycerol) but it performs better in ten other categories. Sensitivity analyses suggest that that the impacts of the physico-chemical treatment are highly dependent on crude glycerol composition, allocation of burdens to crude glycerol and credits for glycerol production. For example, treating crude glycerol with lower glycerol content would increase all impacts except climate change and fossil depletion due to the higher consumption of chemicals and lower production of purified glycerol. Considering crude glycerol as a useful product rather than waste and allocating to it burdens from biodiesel production would increase most impacts significantly, including climate change (22-40 %), while fossil depletion, freshwater and marine eutrophication would become net-positive. The findings of this research will be of interest to the biodiesel industry and other industrial sectors that generate crude glycerol as a by-product.

Insights into Full-congener Profiles of Chlorinated Benzenes in Fly and Bottom Ash: Case Study in Vietnamese Industrial and Municipal Waste Incinerators.

Chlorinated benzenes (CBzs) are a group of organic pollutants, which have been industrially or unintentionally produced through various chemical and thermal processes. Studies on full congener profiles of CBzs in waste and environmental samples are relatively limited and not updated. In the present study, concentrations of 12 CBzs were determined in fly ash (FA) and bottom ash (BA) samples collected from one municipal waste incinerator (MWI) and one industrial waste incinerator (IWI) in northern Vietnam. Levels of Σ12CBzs were higher in bottom ash (median 25.3; range 1.59-45.7 ng/g) than in fly ash (median 7.30; range 1.04-30.0 ng/g). The CBz profiles were dominated by di- and tri-chlorinated congeners with the major congeners as 1,2,4-TCB, 1,2,3-TCB, 1,2-DCB, and 1,3-DCB. However, CBz profiles varied greatly between sample types and incinerators, implying differences in input materials, formation pathways, and pollutant behaviors. Incomplete combustion is possibly responsible for high levels of CBzs in industrial bottom ash. The emission factors of Σ12CBzs ranged from 21 to 600 µg/ton for fly ash and from 190 to 4570 µg/ton for bottom ash, resulting in annual emissions of about 6 and 3 g/year for the IWI and MWI, respectively. Our results suggest additional investigations on industrial emission and environmental occurrence of all 12 CBzs rather than solely focusing on regulated congeners like hexachlorobenzene and pentachlorobenzene.

Preparation of phosphorus containing products by co-incineration of sludge ash and calcium-based additives: Focusing one-step and multi-step method.

Due to the irreplaceable nature of phosphorus (P) in biological growth and the shortage of P rock, it is necessary to recover P from waste, such as sludge ash. P-containing products were prepared using sludge ash and calcium-based additives (CaCO3 and eggshell). In addition, the effects of different incineration methods (one-step method (OSM) and multi-step method (MSM)), additive doses, and incineration temperature on the P content and species in the products were investigated. The results indicated that as the dose of calcium-based additives increased, total P (TP) content in P-containing products reduced, apatite P (AP) content increased, non-apatite P (NAIP) content declined, and P solubility in citric acid content decreased. The amount of AP increased, NAIP reduced, and P solubility in citric acid decreased as the incineration temperature climbed. Although P in P-containing products prepared by OSM and MSM changed in a similar way at different additive doses and temperatures, P-containing products prepared by MSM had at least a 6.1% increase in P solubility in citric acid. Compared with OSM, MSM could save 10% of calcium-based additives when reaching the maximum AP value. Additionally, pure materials were employed to investigate how P species changed during the incineration procedure. The advantage of the MSM-prepared product over the OSM-prepared product may be explained by the high concentration of Ca3(PO4)2 and low concentration of amorphous calcium bound P (Ca-P). Overall, MSM is an effective method to reduce the dose of calcium-based additives and increase the bioavailability of P in P-containing products.

Medical waste incineration fly ash-based magnesium potassium phosphate cement: Calcium-reinforced chlorine solidification/stabilization mechanism and optimized carbon reduction process strategy.

The traditional solidification/stabilization (S/S) technology, Ordinary Portland Cement (OPC), has been widely criticized due to its poor resistance to chloride and significant carbon emissions. Herein, a S/S strategy based on magnesium potassium phosphate cement (MKPC) was developed for the medical waste incineration fly ash (MFA) disposal, which harmonized the chlorine stabilization rate and potential carbon emissions. The in-situ XRD results indicated that the Cl- was efficiently immobilized in the MKPC system with coexisting Ca2+ by the formation of stable Ca5(PO4)3Cl through direct precipitation or intermediate transformation (the Cl- immobilization rate was up to 77.29%). Additionally, the MFA-based MKPC also demonstrated a compressive strength of up to 39.6 MPa, along with an immobilization rate exceeding 90% for heavy metals. Notably, despite the deterioration of the aforementioned S/S performances with increasing MFA incorporation, the potential carbon emissions associated with the entire S/S process were significantly reduced. According to the Life Cycle Assessment, the potential carbon emissions decreased to 8.35 × 102 kg CO2-eq when the MFA reached the blending equilibrium point (17.68 wt.%), while the Cl- immobilization rate still remained above 65%, achieving an acceptable equilibrium. This work proposes a low-carbon preparation strategy for MKPC that realizes chlorine stabilization, which is instructive for the design of S/S materials.

Experimental study on municipal solid waste incineration bottom ash as a component of alkali-activated coal gangue-based geopolymer.

This study explores the potential of municipal solid waste incineration bottom ash (MSWI BA) and coal gangue as precursors for alkali-activated cementitious materials (CG-MBA). An examination of the impact of MSWI BA content, NaOH/Na2SiO3 ratio, liquid-solid ratio, and NaOH concentration on strength and reaction through the application of diverse analytical methodologies. Results demonstrate that CG-MBA offers significant environmental benefits compared to conventional cement. When used as a construction filling material, CG-MBA exhibits a remarkable 74.5 ~ 79.2 wt% reduction in carbon dioxide emissions and 70.6 ~ 77.0 wt% reduction in energy consumption. Additionally, CG-MBA effectively immobilizes heavy metal ions in MSWI BA, with a fixation efficiency exceeding 56.0%. These findings suggest that CG-MBA is a promising sustainable solution for waste management, offering significant environmental benefits while demonstrating effective heavy metal immobilization. This approach contributes to pollution control and promotes environmental sustainability in the construction industry.

Characterization of lightweight aerated mortars using waste-to-energy bottom ash (WtE-BA) as aerating agent.

The management of Waste-to-Energy Bottom Ash (WtE-BA), generated during the incineration of waste, poses a global challenge. Presently, the majority of WtE-BA is disposed of in landfills due to the lack of alternatives. Meanwhile, the construction industry remains the primary consumer of raw materials and significantly contributes to Greenhouse Gas Emissions. This study attempts to address these issues by utilizing the fine fraction of WtE-BA (<2 mm) as a raw material for aerated mortar production. Thanks to its metallic aluminum content, WtE-BA is utilized as an aerating agent. The study investigates how the quantities of water and WtE-BA, as well as its granulometric sub-fractions, impact the properties of the final product. An analysis of properties such as density, compressive strength, and thermal conductivity was conducted. Additionally, the environmental impact of each raw material (i.e. WtE-BA, cement and sand) was assessed through leaching tests and elemental content analysis enabling the determination of their individual contribution to the presence of trace elements in the produced mortars. The aforementioned properties are discussed using microstructure and porosity analyses. The findings demonstrate that the quantity of water is a crucial factor in controlling the aeration of mortars, whereas the granulometry of the WtE-BA particles did not significantly affect their macro-properties. Furthermore, this study highlights that WtE-BA based mortars has the potential to exhibit better environmental and insulating performances than standard aerated mortar of equal density and strength. The differences in pore size and type between WtE-BA and aerated mortars can account for the variation in performance. Thus, WtE-BA proves to be an effective substitute for aerating agent in the production of aerated mortars.

Environmental performance of unfired bricks produced from co-disposal of mine tailings and municipal solid waste incineration fly ash based on comprehensive leaching tests.

The potential leaching of heavy metals is a crucial concern for construction materials produced from solidification/stabilization (S/S) treatment of wastes. This study comprehensively evaluated the leaching characteristics of heavy metals from the unfired bricks produced from co-disposal of Pb-Zn mine tailings and municipal solid waste incineration fly ash using batch, sequential, and semi-dynamic leaching tests. The results show that S/S treatment drastically reduced the leachability of heavy metals from the unfired bricks through lowering their distribution in the acid-soluble fraction. The effective diffusion coefficients of heavy metals within unfired bricks were all below 1.55 × 10-13 cm2/s, which is indicative of low mobility in the environment. The release of heavy metals from the unfired bricks was primarily governed by diffusion and dissolution. Slaking treatment of fly ash significantly reduced the leaching of heavy metals from the unfired bricks due to their improved structural integrity and compactness, which minimizes the surface area in the solid matrix accessible by the leaching medium. The leachability indices of heavy metals within the unfired bricks ranged from 13.12 to 18.10, suggesting that they are suitable for "controlled utilization" in specific scenarios. Compared to untreated mine tailings, converting them into unfired bricks could reduce the releases of heavy metals by several to hundreds of folds. These findings demonstrate that S/S can be an effective and sustainable strategy for co-disposal of mining tailings and incineration fly ash to produce construction materials with sound long-term environmental performance.

Exposure estimation and neurotoxicity inhibition of dioxins in sensitive populations near domestic waste incineration plant through adverse outcome pathway.

The neurotoxicity induced by dioxins has been recognized as a serious concern to sensitive population living near waste incineration plants. However, investigating the intracellular neurotoxicity of dioxin in humans and the corresponding mitigation strategies has been barely studied. Thus, a domestic waste incineration plant was selected in this study to characterize the neurotoxicity risks of sensitive populations by estimating the ratio of dioxin in human cells using membrane structure dynamics simulation; and constructing a complete dioxin neurotoxicity adverse outcome pathway considering the binding process of AhR/ARNT dimer protein and dioxin response element (DRE). Six dioxins with high neurotoxicity risk were identified. According to the composite neurotoxicity risk analysis, the highest composite neurotoxicity risk appeared when the six dioxins were jointly exposed. Dietary schemes were designed using 1/2 partial factor experimental design to mitigate the composite neurotoxicity risk of six dioxins and No. 16 was screened as the optimum combination which can effectively alleviate the composite neurotoxicity risk by 29.52%. Mechanism analysis shows that the interaction between AhR/ARNT dimer protein and DRE was inhibited under the optimal dietary scheme. This study provides theoretical feasibility and reference significance for assessing composite toxicity risks of pollutants and safety mitigation measures for toxic effects.

Effect of long-term dry-wet circulations on the Solidification/stabilization of Municipal solid waste incineration fly ash using a novel cementitious material.

Solidification/stabilization (S/S) is a typical technique to immobilize toxic heavy metals in Municipal solid waste incineration fly ash (MSWI FA). This study utilized blast furnace slag, steel slag, desulfurization gypsum, and phosphoric acid sludge to develop a novel metallurgical slag based cementing material (MSCM). Its S/S effects of MSWI FA and long-term S/S effectiveness under dry-wet circulations (DWC) were evaluated and compared with ordinary Portland cement (OPC). The MSCM-FA block with 25 wt.% MSCM content achieved 28-day compressive strength of 9.38 MPa, indicating its high hydration reactivity. The leaching concentrations of Pb, Zn and Cd were just 51.4, 1895.8 and 36.1 µg/L, respectively, well below the limit standard of Municipal solid wastes in China (GB 16889-2008). After 30 times' DWC, leaching concentrations of Pb, Zn and Cd for MSCM-FA blocks increased up to 130.7, 9107.4 and 156.8 µg/L, respectively, but considerably lower than those for OPC-FA blocks (689, 11,870.6 and 185.2 µg/L, respectively). The XRD and chemical speciation analysis revealed the desorption of Pb, Zn and Cd attached to surface of C-S-H crystalline structure during the DWC. The XPS and SEM-EDS analysis confirmed the formation of Pb-O-Si and Zn-O-Si bonds via isomorphous replacement of C-A-S-H in binder-FA blocks. Ettringite crystalline structure in OPC-FA block was severely destructed during the DWC, resulting in the reduced contents of PbSO4 and CaZn2Si2O7·H2O and the higher leachability of Pb2+ and Zn2+.

Preparation of functional geopolymers from municipal solid waste incineration fly ash: An approach combining experimental and computational simulation studies.

This study aims to evaluate the feasibility and safety of using municipal solid waste incineration fly ash (MSW-IFA) in the development of geopolymer-based solidification/stabilization (S/S) treatments. Geopolymers have garnered attention as a sustainable alternative to traditional cement, owing to their high strength, stability, and minimal CO2 emissions. In this study, a combination of experimental and simulation calculations was used to investigate the setting time, mechanical properties, environmental risks, hydration mechanisms and processes of municipal solid waste incineration fly ash-based polymeric functional cementitious materials (GFCM). The results demonstrate that the mechanical properties of GFCM are related to the changes in the mineral phases and the degree of compactness. Quantum chemical calculations indicate that the hydration products may be [Si(OH)4], [Al(OH)3(OH2)] and [Al(OH)4]-. It is possible that the heavy metals are embedded in the hydrated silica-aluminate by electrostatic interaction or chemisorption. Heavy metals may be embedded in hydrated silica-aluminate by electrostatic action or chemisorption. This study provides a feasible method for resource utilization and heavy metal stabilization mechanism of MSW-IFA.

New multi-source waste co-incineration and clustering park operating model for small- and medium-sized city: A case study in China.

With improvements in urban waste management to promote sustainable development, an increasing number of waste types need to be sorted and treated separately. Due to the relatively low amount of waste generated in small- and medium-sized cities, separate treatment facilities for each waste type lack scale, waste is treated at a high cost and low efficiency. Therefore, industrial symbiosis principles are suggested to be used to guide collaborative waste treatment system of multi-source solid wastes, and co-incineration is the most commonly used technology. Most existing studies have focused on co-incineration of one certain waste type (such as sludge or medical waste) with municipal solid waste (MSW), but the systematic design and the comprehensive benefits on a whole city and park level have not been widely studied. Taking the actual operation of a multi-source waste co-incineration park in south-central China as an example, this study conducted a detailed analysis of the waste-energy-water metabolism process of MSW, sludge, food waste, and medical waste co-incineration. The environmental and economic benefits were evaluated and compared with the single decentralized waste treatment mode. The results showed that the multi-source waste co-incineration and clustering park operating model was comprehensively superior to the single treatment mode, greenhouse gases and human toxicity indicators were decreased by 11.87% and 295.74%, respectively, and the internal rate of return of the project was increased by 29.35%. This mainly benefits from the synergy of technical system and the economies of scale. Finally, this research proposed policy suggestions from systematic planning and design, technical route selection, and an innovative management mode in view of the potential challenges.

Categorization of leaching behaviors of elements from commercially treated incineration bottom ash in Singapore.

Leaching of potentially hazardous substances, especially the heavy metals from Incineration Bottom Ash (IBA) is a major problem in its recyclable usage. To address this concern, treatment of IBA is indispensable before it can be reused. IBA subjected to laboratory-scale treatment typically yields clearer conclusions in terms of leaching behaviors, benefiting from the controlled laboratory environment. However, the leaching behaviors of commercially treated IBA appear to be more ambiguous due to the complex and comprehensive nature of industrial-scale treatments, where multiple treatment techniques are involved concurrently. Furthermore, treatment efficiencies vary among different plants. In this study, three types of commercially treated IBA were sampled from leading waste treatment companies in Singapore. Characterization and leaching tests were performed on the treated IBAs in both standardized and modified manners to simulate various scenarios. Besides deionized water, artificial seawater was used as a leachant in leaching tests for simulating seawater intrusion. The results reveal the promoting effect of seawater on the leaching levels of several elements from three types of treated IBA, which may require special attention for IBA application and landfill near the coast. Furthermore, the elements examined in these three types of commercially treated IBA generally comply with the non-hazardous waste acceptance criteria outlined in Council Decision, 2003/33/EC (2003), except Sb. By combining two leaching tests, the elements were categorized into different types of leaching behavior, making it possible to prepare and respond to the concerning leaching scenarios in future engineering applications.

Health assessment of emerging persistent organic pollutants (POPs) in PM2.5 in northern and central Taiwan.

Over the last two decades, Taiwan has effectively diminished atmospheric concentrations of polychlorinated dibenzo-p-dioxins/furans (PCDD/Fs) through the adept utilization of advanced technologies and the implementation of air pollution control devices. Despite this success, there exists a dearth of data regarding the levels of other PM2.5-bound organic pollutants and their associated health risks. To address this gap, our study comprehensively investigates the spatial and seasonal variations, potential sources, and health risks of PCDD/Fs, Polychlorinated biphenyls (PCBs), and Polychlorinated naphthalene (PCNs) in Northern and Central Taiwan. Sampling collections were conducted at three specific locations, including six municipal waste incinerators in Northern Taiwan, as well as a traffic and an industrial site in Central Taiwan. As a result, the highest mean values of PM2.5 (20.3-39.6 µg/m3) were observed at traffic sites, followed by industrial sites (14.4-39.3 µg/m3), and the vicinity of the municipal waste incinerator (12.4-29.4 µg/m3). Additionally, PCDD/Fs and PCBs exhibited discernible seasonal fluctuations, displaying higher concentrations in winter (7.53-11.9 and 0.09-0.12 fg I-TEQWHO/m3) and spring (7.02-13.7 and 0.11-0.16 fg I-TEQWHO/m3) compared to summer and autumn. Conversely, PCNs displayed no significant seasonal variations, with peak values observed in winter (0.05-0.10 fg I-TEQWHO/m3) and spring (0.03-0.08 fg I-TEQWHO/m3). Utilizing a Positive Matrix Factorization (PMF) model, sintering plants emerged as the predominant contributors to PCDD/Fs, constituting 77.9% of emissions. Woodchip boilers (68.3%) and municipal waste incinerators (21.0%) were identified as primary contributors to PCBs, while municipal waste incinerators (64.6%) along with a secondary copper and a copper sludge smelter (22.1%) were the principal sources of PCNs. Moreover, the study specified that individuals aged 19-70 in Northern Taiwan and those under the age of 12 years in Central Taiwan were found to have a significantly higher cancer risk, with values ranging from 9.26 x 10-9-1.12 x 10-7 and from 2.50 x 10-8-2.08 x 10-7respectively.

Synergistic control potential of flue gas pollutants under Ultra-Low emission standards in waste incineration plants.

As the dominant waste disposal process, incineration is regarded as the main incentive for the "not-in-my-backyard" syndrome, and faces an inescapable pressures of ultra-low emissions (ULE). Establishing precise response relationships between emission factors (EFs) and full-process influencing factors can provide guidance for the synergistic mitigation of flue gas pollutants (FGPs). In this work, the multi-dimensional EFs of FGPs were identified by initially integrating FGPs concentration monitoring data of existing 1,226 processing lines in China, technologies applied and operational experience (OE), local economic and political characteristics. Significant regional imbalance performance was observed, which EFs in the coastal regions were 3.55-92.39 % lower than those of the inland areas. NOx, SO2, HCl were identified as critical components requiring further reduction under the ULE standards, with exceedance rates recorded at 73.07 %, 38.90 %, and 56.69 %, respectively. An indicative value of 20 mg/m3 for PM is recommended for the control of heavy metals of Cd + Tl and Sb + As + Pb + Cr + Co + Cu + Mn + Ni based on the correlation coefficients of r = 0.28 (p < 0.001) and r = 0.20 (p = 0.002), respectively. Waste composition and OE were quantified as the main contributors of EFs' disparities by the tree-branching controlled variable approach established in this study. Predictive models for FGPs control process and corresponding EFs were constructed. EFs of nine FGPs in 2030 would decrease by 0.97-65.42 %, due to more complex purification processes employed to meet ULE's limitations, such as the application of five-stage processes growing from 45.60 % to 58.28 %. While regional imbalance in EFs-SO2 and EFs-HCl were extended with increases from 25.83 % to 33.07 % and 9.91 % to 32.32 %, respectively, due to the consistent disparities of OE and growing heterogeneity of control policies. Enhancing interregional empirical exchanges, reducing the regional market monopolies, and formulating technical guidelines would be beneficial to synergize the reduction of FGPs emissions and alleviate regional imbalance.

Probabilistic human health risk assessment of PCDD/Fs near municipal solid-waste incinerator using Monte Carlo analysis coupled with triangular fuzzy numbers.

PCDD/Fs are dioxins produced by waste incineration and pose risks to human health. We aimed to detail the health risks of airborne and soil PCDD/Fs near a municipal solid-waste incinerator (MSWI) for the surrounding population and develop a new model that improves upon existing methods. Thus, we conducted field sampling and then investigated a MSWI in the Pearl River Delta (2016-2018). Our results showed that the carcinogenic and non-carcinogenic risk values of PCDD/Fs exposed to residents in nearby areas were acceptable, with hazard index (HI) values lower than 1.0 and a total carcinogenic risk lower than 1.0E-6. Notably, the results raised concerns regarding higher non-carcinogenic risks in children than in adults. Comparative analysis of the frequency accumulation diagram, accumulated probability risk, and the absolute value of error (δ) between the 95% confidence interval (CI) and the 90% CI of the Monte Carlo stochastic simulation-triangular fuzzy number (MCSS-TFN) and the MCSS model, respectively, demonstrated that the MCSS-TFN exhibited less uncertainty than the MCSS model, regardless of the health risk value of PCDD/Fs in ambient air or in soil. This observation underscores the superiority of the MCSS-TFN model over other models in assessing the health risks associated with PCDD/Fs in situations with limited data. Our new method overcomes the limited dataset size and high uncertainty in assessing the health risks of dioxin substances, providing a more comprehensive understanding of their associated health risks than MCSS models.

Fate of perfluoroalkyl and polyfluoroalkyl substances (PFAS) through two full-scale wastewater sludge incinerators.

Perfluoroalkyl and polyfluoroalkyl substances (PFAS) are an emerging issue in wastewater treatment. High-temperature thermal processes, incineration being time-tested, offer the opportunity to destroy and change the composition of PFAS. The fate of PFAS has been documented through wastewater sludge incinerators, including a multiple hearth furnace (MHF) and a fluidized bed furnace (FBF). The dewatered wastewater sludge feedstock averaged 247- and 1280-µmol targeted PFAS per sample run in MHF and FBF feed, respectively. Stack emissions (reportable for all targeted PFAS from MHF only) averaged 5% of that value with shorter alkyl chain compounds comprising the majority of the targeted PFAS. Wet scrubber water streams accumulated nonpolar fluorinated organics from the furnace exhaust with an average of 0.740- and 0.114-mol F- per sample run, for the MHF and FBF, respectively. Simple alkane PFAS measured at the stack represented 0.5%-4.5% of the total estimated facility greenhouse gas emissions. PRACTITIONER POINTS: The MHF emitted six short chain PFAS from the stack, which were shorter alkyl chain compounds compared with sludge PFAS. The FBF did not consistently emit reportable PFAS from the stack, but contamination complicated the assessment. Five percent of the MHF sludge molar PFAS load was reported in the stack. MHF and FBF wet scrubber water streams accumulated nonpolar fluorinated organics from the furnace exhaust. Ultra-short volatile alkane PFAS measured at the stack represented 0.5%-4.5% of the estimated facility greenhouse gas emissions.